ÍÀÇÀÄ

GLADIATOR

G-30

Owner's Manual

FEATURES:

OPTIONAL FEATURES:

Ðèñ. 1

WARNING! CHANGE BATTERY WHENREMOTE RANGE IS GETTING SHORT

Remote Features:

Each alarm is assorted with two special transmitters. Hi-tech hopping code system is applied to each transmitter. This system has supper confidential technology. It can hardly possible be copied. It is used high stable UHF frequency as radio transmission circuit. For your operation convenience, four transmitters can be learn into this alarm at the same time. Transmitter's battery use: 12V GP23A

REMOTE FUNCTION TABLE

Press 1 Button once Arm / Door Lock
Hold 1 Button for 2 seconds Arm Without Siren/Horn Chirp
Press 1 Button once after 10 sec. armed Car finder
Press 1 Button once after set Arming 1st stage - Sensors by Pass
Press 1 Button twice after set Arming 2nd stage - Sensors by Pass
Press 2 Button Disarm / Door unlock
Hold 2 Button for 2 seconds Disarm Without Siren/Horn Chirp
Press 3 Both buttons once Panic / Anti Car-Jack (ACC ON)
Hold 3 Both buttons for 2 seconds Trunk Opener

Sub-Function Setting

In Disarm position. Turn off IGN ,within 10 seconds press valet SW 5 times, until siren /horn chirp 4 times and lights ON means system entering in programmable mode. The times of valet SW pressing is according to the function item number. To judge it as per LED indication (times of flashes). E.g. to set sub-function item No.2: Press valet SW 2 times, LED quick flash 2 times after a pause. Then press remote to select ON or OFF . To press 1 button function will be ON, siren/horn will giving two chirps. To press 2 button function will be OFF, siren/horn will giving four chirps.

SUB-FUNCTION TABLE

Item No. Function ON OFF
1 Immobilizer (smart engine disable) YES * NO
2 Passive arming function setting (door lock) YES * NO
3 Passive arming function setting (door without lock) YES * NO
4 Door switch arming detection delay * 0 sec. 45 sec.
5 Safety Door Lock * YES NO
6 Unlock output 1 or 2 pulse selection * 1 pulse 2 pulse
7 Siren / Horn Selection * Siren Horn
8 Anti car-jacking mode selection * Active Passive

Note: * means factory setting before delivery.

If the above condition happens , alarm will exit this setting mode by turn IGN to ON position or within 10 seconds there is no setting activity , Lights will OFF.

How to use code learning:

This system can expand 4 different transmitters, and comes from factory with two transmitters already programmed into the system memory. When ever you want to add or delete transmitter code of the system, the procedures are as following:

  1. In Disarm position. Turn ON IGN , within 10 seconds press valet SW 5 times.
  2. Siren/Horn will chirp 3 times and Lights ON to confirm the system is in code learning mode.
  3. To press any remote button, code learning achieved if it gives one short chirp.
  4. To turnoff learning mode: (1) Turn off IGN. (2) Four transmitters have been successfully learnt already (3) Within 10 seconds, there is no new transmitter be learnt. Lights OFF to confirm Exit this mode.

Standard features:

  1. To Arm the system: Press button 1 siren/horn will chirp once, lights flash once and LED will flash slowly. Doors locked , start killed and controller to close all windows. Alarm will be triggered whenever the car was hit orintruded
  2. To Arm the system without Siren/Horn chirp: To hold 1 button for over 2 seconds, light flash one but no chirp sound, other functions are the same as Arm .(This feature to prevent noise in silent area)
  3. To Disarm the system: Press button 2 siren will chirp twice, lights flash twice and LED will be off. Doors unlocked and start killer released
  4. To Disarm the system without Siren/Horn chirp: To hold button for over 2 seconds, light flash twice but no chirp sound, other function as the same as Disarm.(This feature to prevent noise in silent area)
  5. Panic: Press button 3 , panic mode will be activated . Siren will burst and lights will flash for 29 seconds, until press any button to turn off the panic mode.
  6. Remote Trunk Release: Keep press button 3 for over 2 seconds then trunk will automatically opened. During Arming ,remote trunk release will not trigger alarm and sensor trigger function will also shut off, but IGN and doors keep arming condition. After closed trunk for5 seconds ,trunk and sensor trigger will return to arm status.
  7. Auto Re-Arming: Alarm arms again30 seconds after disarm, unless the doors have been opened or engine is ignition on. This feature is to avoid mis-touch or mis-disarmed.
  8. Alarm Abnormal Arming Indication: Inarmingmodeifthesirenchirps4timesandlightflash4 times it reminder you that door(s)is not shut properly. If siren chirps 5 times it reminder you that hood or trunk is not closed . The alarm will bypass that zone and it will still protect other zones.
  9. 2nd Killer Output: This feature can be controlled separately of the engine disable. This output (-5 00mA) is working with system disarmed. 40A relay is required and go with 40Arelay (N/O &COM) output.
  10. Passive Arming: If you want to use this function, set itemNo.2 or itemNo.3 on "ON "position. While you turn off IGN, open door then close door, LED will quick flash. After 30seconds alarm will armed automatically ,but during 30seconds, if any of the door, trunk, hood is open, alarm will stop this" passive arming".
  11. Alarm T rigger : During arming, if turn on IGN, open door, and etc...alarm will trigger in order to stop the offender.

    * When triggering 1st stage sensor: Siren/Horn gives one long chirp for warning.

    * When triggering 2nd stage sensor: Siren/Horn gives 20seconds sound and light flash 20seconds. there is only 6 times trigger imitation after the alarm is in armed status every each time.

    * When triggering IGN, door, hood or trunk and etc.: Siren/Horn gives 29 seconds sound and light flash 29 seconds.

    After alarm triggering there is 2seconds pause. The alarm will detect to see if it is recovered to normal arming condition. If it is not, the alarm will trigger again.

  12. Remote Sensor by Pass: The alarm offers two stage sensor optional. Within 10seconds after set arming, to press 1 button once, siren/horn will chirp twice, then 1st stage sensor by pass. to press 1 button twice, siren/horn will chirp 3 times then all sensors will be shut off and no sensor working for arming protection. If in silent mode, lights flash will instead siren chirps.
  13. Car Finder: If your car in crowded big parking place ,you can easy to find your car position by press button 1 once. Siren chirp once follow with lights flashing for 30sec. If press button 1 for 2 sec. Lights flashing 30 sec. But without siren chirp. Note: Such feature operate after 10sec.Once entering in arm position.
  14. Valet mode: turn Ignition on, within 10 seconds hold valet switch for over 5 seconds , LED will be on indicating in the Valet mode. Under this mode, remote lock and unlock is still effective and other functions are shut off temporary. Mode exiting : In IGN ON , hold valet switch for over 5 seconds, LED will be off means exit of Valet mode.
  15. Alarm Trigger memory: In arm status if anything triggers, after you disarm, siren/horn will sound and light will flash 4 times indicating that alarm was triggered before .LED mode indicates the following different triggering :
    Quick flash 2 times after a pause Sensor 1st stage trigger
    Quick flash 3 times after a pause Sensor 2nd stage trigger
    Quick flash 4 times after a pause Door trigger
    Quick flash 5 times after a pause Engine hood or trunk trigger
    Quick flash 6 times after a pause IGN trigger
  16. Smart Engine Disable (immobilizer): Set sub-function Item NO.1 to "ON" position.

    After turn off IGN position for 2 minutes or you open and close door in 2 minutes after turn off IGN, it will start engine disable function right To disarm this function, turn IGN on, within 10 seconds, press Valet SW for 5sec. and into valet mode. Or simply press button 2 once and into normal status.

  17. Power disconnecting memory: This system is built in memory on main unit. Generally, after alarm power is cut and reconnect, main unit will read back these data make the alarm to resume. When in disarm, arm or valet mode, anti car-jacking mode power off then on again, alarm will read back original position.
  18. Safety door lock/unlock: To use this function, set sub-function NO.5 to "ON". After closer last door, turn on IGN for 10 seconds all doors will auto lock for protection. To turn off IGN, all doors will auto unlock for take off conveniently
  19. Window (-) Output: This channel is a negative (-500mA) output features. To operated this option when equipped, simply press button, system will armed and window roll-up/down approximately 30 seconds.
  20. Parking lights relay built-in: This system is build-in with a double-side point relays for Right and Left two side turning indicator.
  21. Central door lock relays built-in: This system is build-in relays for door lock/unlock and available for any different design of car .
  22. Pager output: Pager(-)500mA output can be connected to alarm pager to become two way service.
  23. Anti car-jack: This feature will protect your vehicle in the event that there is an attempt to Hi-jack the vehicle. There are three ways to activate this feature. While system is trigger anti-car jack mode, Lights will flash 3 times and the LED will fast flashing to show the system is enter anti-carjacking mode. See under 24 "anti-car jack mode table".
    1. REMOTE ANTI-CAR JACK: While Ignition ON, Press button © once . The parking lights will flash 3 times and the LED will fast flash to show the system is enter anti car-jack mode.

      TO EXIT: Within 60sec. after enter this mode, simply press button once , or Acc on press valet switch once LED off to confirm exit mode.

      NOTE: After 60sec., to exit this mode must use your PIN code to disarm your system, please see "How to use your PIN code".

    2. ACTIVE ANTI-CAR JACK: To install this optional anti-car jack switch contact your dealer and Set sub-function Item No.8 to "ON" position. This switch is not a switch at all. It is a factory switch already in your vehicle that will function Anti car-jack mode by Push or turn ON this switch. Any factory switch in the vehicle maybe used, as long as it switches positive voltage .Ask your customer to determine which switches will work in the vehicle. Some possible switches are light switch, radio turn-on, or defroster switches. During this switch is turned ON, while door's been open system will enter anti-car jack mode.

      TO EXIT: Within 60sec. after enter this mode, In Acc on, Push or turn anti-car jack switch OFF or press valet switch once LED off to confirm exit this mode.

      NOTE: After 60sec., to exit this mode must use your PIN code to disarm your system, please see "How to use your PIN code".

    3. PASSIVE ANTI-CAR JACK: If set sub-function Item No.8 to "OFF" set, system will automatic enter anti car-jack mode, when you open one of the door in Ignition on position.

      TO EXIT: Within 60sec. after enter this mode, In Acc on, press valet switch once LED off to confirm exit this mode.

      NOTE: After 60sec., to exit this mode must use your PIN code to disarm your system, please see "How to use your PIN code".

  24. Anti car-jack mode table: If enter anti car-jack mode, Parking lights will flashing 3 times and LED will fast flashing to show the system is enter anti car-jack mode.
    Ðèñ. 2
  25. How to use your PIN code: If you are in Anti carjack mode after 60 sec. Or system in triggering, you can manually disarm your system by enter your own PIN code. (The system's factory-set PIN code is 1.1 )
    1. Turn Ignition "OFF then ON" LED will go OFF,
    2. Press and hold valet switch, LED will start flashing, the times of LED flashing is according to the PIN codes number.
    3. To set your 1st PIN code (1) , press and hold valet switch, while LED flash 1 time then release valet switch LED will OFF, means your 1st PIN code (1) been programmed.
    4. To set your 2nd PIN code (1) , press and hold valet switch, while LED flash 1 time then release valet switch LED will OFF, means your 2nd PIN code (1) been programmed.
    5. After 2-digit PIN code been programmed, system will be disarmed.
  26. Set your own PIN code: Choose any 1-2-digit code, but the 2digit code must not be a zero. For example: Let's say you want to set a password of " 9.1 " , Turn Ignition ON then OFF, within 10 sec., Press and hold valet switch for 5sec. Until siren give 2 chirps and Lights ON, means enter this mode, release valet switch. Upon program mode, press and hold valet switch, LED will start flashing, the times of flashing is the number of 1st PIN code, while flash 9 times, release valet switch and your 1 st code been programmed. To set 2nd PIN code, press and hold valet switch again, while LED flash 1 time, release valet switch and your 2nd code been programmed. If 2-digit codes been programmed, siren will chirp 9 and 1 to sound your new PIN codes and into normal status, hence your new PIN codes been programmed and Light will turn off automatically.

System wiring diagrams

Ðèñ. 3


Ðèñ. 4
16.01.2004