Slow flash: Arm / alarm / panic / anti-hijack.
Fast flash: Auto re-arm.
Steady light: Last door arming / send message to controller.
No light: Disarming mode.
Note: Main unit will not accept the command during sending message to controller.
This alarm system can expand to four units of transmitter and comes from the factory with one 2-Way LCD screen 4 button remote controller and one 3 button without LCD screen spare remote controller, which is programmed into the system memory. Following the steps below to enter learning code procedure.
(Also it will be off of learning procedure automatically while all 4 remote controllers have finished learning code in the memory.)
Button | Ignition Off | Ignition On | Engine Start in Arm Mode |
---|---|---|---|
Press Button (1) | Arm / Car Search | Lock | Lock |
Press Button (2) | Disarm | Unlock | Disarm/unlock |
Press Button (3) | Remote Start On/Off | Kill Engine | |
Press Button (4) for 1 sec. | Start Arm/Silent Car Search | ||
Press Button (1) over 2 sec. | Remote Panic | Anti-Hijacking | |
Press Button (2) over 2 sec. | Trunk Release | Driving Lock Mode On/Off | Disarm & Trunk Release |
Press Button (1)+(2) for 2 sec. | Last Door Arming On/Off | ||
Press Button (2)+(3) for 2 sec. | Crank time Setting | ||
Emergency Reset | a) Open a door & pull down the hand brake b) Switch ignition on/off 5 times |
Under the disarm mode, press button (1), siren will chirp once, lights flash once, doors lock, engine killer is on, LED flashes rapidly and 5 seconds later flashes slowly, and the system enters into the arm mode. During the period of 5-second fast LED flash, if the ignition, door sensors or pin sensors are triggered, the impact will still be memorized. When enter into the arm code, the alarm will sound. But if the shock sensor is triggered, the impact will not be memorized.
Before entering into the arm mode, if doors are opened or start kill is on, when enter into the arm mode, siren will chirp three times. This means sensors are activated. These three sensors will be bypassed until doors are closed and start kill is off.
Under the arm mode, press button (1) once, siren will sound a long chirp and lights flash once.
While the ignition is on (driving status) under the disarm mode, press button (1) over 2 seconds and lights will flash. One minute later, siren will be on, start kill is on and door lock, lights keep flashing then enter into the remote anti-hijack status. Pressing button (1) once can release the remote anti-hijack status.
Under the arm mode, press button (1) over 2 seconds, siren will be on and lights flash. Siren and lights will be off after 60 seconds and the system is still under the arm mode.
Under the disarm mode, press button (1) over 2 seconds, siren will be on and lights flash. Siren and lights will be off after 60 seconds. After 30-second fast flash in LED, siren chirps once, start kills is on and enter into the arm mode.
Under the panic mode, press button (1) and will release the panic mode.
Under the disarm mode, switch the ignition on, press button (2) once after 3 seconds, door unlock can be controlled. Pressing button (1) once more can control door lock.
Last door arming is set: Under the disarm mode, switch ignition on/off and door sensor is on/off, then LED is on. The system will enter into the arm mode after 30 seconds.
Last door arming is released: Under the disarm mode, switch ignition on/off and door sensor is on/off, then the system will not automatically enter into the arm mode.
Under the disarm mode, switch the ignition on and press button (1)+(2) once, lights will flash once. Press button (1)+(2) once more within 2 seconds, siren will chirp once and LED is on then the system enters into the valet mode. Under the valet mode, only can use button (1) to control door lock and button (2) to control unlock.
Switch the ignition on and then press button (1)+(2) once, lights flash once. Press (1)+(2) once more within 2 seconds, siren will chirp once and the system quits the valet mode.
Under the arm mode, press button (2) over two seconds, truck will be opened and lights flash twice. Auto re-arm will also not be activated.
*Press button (3) once, siren will chirp once, lights flash once and, ACC and the ignition are on. Seven seconds later, the igniting action starts, ACC is off. The igniting time is up, the igniting action is off, ACC will be on and lights will flash. This means the igniting action succeeds and keeps running for 6 minutes.
*If the handbrake is off, can't start the engine, siren will chirp twice and the system will be back to the status when the handbrake is off.
*Press button (3) once, siren will chirp once, ACC and ignition are on, and lights flash once then flash twice later, the igniting action starts, ACC is off. The igniting time is up, the igniting action is off, ACC and ignition will be on and lights will flash. This means the igniting action succeeds and keeps running for 6 minutes.
*While igniting, if the system doesn't receive the signals of charger (-) or starter solenoid (-), the engine start will be failed. There will be five times of automatic igniting actions.
*If handbrake is off, can't start the engine, siren will chirp twice and the system will be back to the status when the handbrake is off.
*When door sensor and pin sensor are triggered, igniting actions will be cancelled, ACC and ignition will be off, lights flash and siren chirps. The system will be back to the arm mode after 60 seconds.
*Press button (2), doors will be unlocked and the system is back to the disarm mode. Pressing button (1) can only control door lock and button (2) can only control unlock but doesn't have trigger alarm functions, and igniting actions remain.
In the main unit, there is a 3-pin housing that is applied for other devices, such as other alarm system. If a car has been installed other alarm system and a user want to install FAI-8000 also, FAI-8000 provide this function to avoid conflicted signals from the other alarm system. However, this function can only be applied when hardware of other devices have same equipments to comply with FAI-8000.
There is a three-pin plug to connect with the housing. In this three-pin plug, the black wire delivers the signal of "Start On", which sends a pre-caution signal to other alarm system that other alarm system should be prepared to disarm the system. The red wire delivers the signal of "Start Running On" after starts the ignition, which requests the other alarm system to be disarmed. The blue wire delivers the signal of "Start Off" after turn off the ignition, which requests the other alarm system to be armed.
This function is optional depending on equipments of other alarm system. If a car only installs FAI-8000, please disregard this function.